Here's another mobile home moving fail story for everyone. Complete fail, long single-wide stuck in a ravine when Phil gets there.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Got a call that a mobile home mover was hung up
00:40 His rollers are $1500 18 years ago, not something you want to loan out
01:20 Way out past Elkins, AR stuck in a ravine
01:30 70' single wide trailer
01:55 Wheels on the ravine side are hanging off the road
02:25 Under the trailer and mobile home, the mover had 3 guys working
02:40 Trailer was above their head almost 7' high
03:00 Telling the 3 guys to get out of the ravine
03:15 Jacked the house up, had to get more stuff to do it
03:45 Ended up moving it 3' at a time 7 times
04:15 Had to jack it up 2 more times because it kept dropping back into the ravine
04:30 20' after the ravine he couldn't go anywhere
04:50 Murphy's law was in full effect
05:00 Normal routine is the driver drives the route, checks it out before they do the move
05:40 The movers had to pay a guy for the tree they needed to cut
06:00 Back the next day in a snow storm
06:25 Had to go straight up through a ditch to get to the property
07:00 Day 2 and running out of daylight again
07:30 The mover decided Phil was in charge
08:00 Trying to get the mobile home up a steep hill and set in place
08:30 Have another heavy duty truck to pull the mobile home, but have to keep it from flipping over
09:00 Moving the mobile home, moving truck 7-10' at a time up the hill
09:30 Stopping for the night just to dangerous to continue
10:10 Three and half days to move the house and set it up

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

Story time, and time to get to know Phil just a little better.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Comedy: that is his life
00:22 One point he was setting up a lot of mobile homes close to 200
01:05 Going to Little Rock to meet the mobile home mover
01:30 Get out to the site
02:00 First half went on pretty easy
02:30 Had guys on the front to direct the mover, and Phil on the back
03:10 The mover could only see Phil's head in the mirror because...
03:25 Phil found the septic tank... The hard way
03:50 Ended up above his knees in septic
04:05 The guys were laughing so hard they couldn't pull him out
04:35 Had to go get hosed off at a car wash
04:50 Had to take turns hosing him down because they couldn't quit laughing
05:10 For months he'd hear do you smell something

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#comedy #storytime #septicfail

Quick review of the Pioneer Inverter Ultra High Efficiency Heat Pump 3 head mini split.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 The instructions left a bit to be desired
00:35 Drains were a bit of a challenge
01:05 The wiring
01:20 Could someone do this easily on their own?
01:35 They do have a quick connect system to look into

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#MiniSplitReview #MiniSplitAC #DuctlessAC

Transcript:
So with the pioneer inverter ultra high efficiency heat pump. The instructions were a lot left to be desired. It was very difficult to get to where we needed to get, but we did get it, particularly Drew. We've got all the lines up, everything's connected. The drains were a little bit of a challenge also because of the distance we're having to carry.

So we put it in two Pexs. One of the connections out of three or four or five connections is not leaking and we don't want that to happen. That is the drain connection. Everything else is working. Kicking out at 62. So Drew and Clay, particularly Drew did a good job getting everything squared away, the wiring. We had a minor problem.

The new, the different style disconnect kind of threw Clay for a loop, but Drew and Clay did a good job on it. Is it something that somebody can do easily on their own? First of all, you would not have the Freon available to you unless you are an air conditioned person. Then all the other tools that require like a vacuum pump and gauges and all those things would probably not be something that you could get your hands on.

They do have, according to Clay, a quick connect set up where the Freon is included. So that would be something I would look into if you were doing it for yourself. Otherwise, this is kind of for the person who is not going to do it to know what should be done or what it could look like and the person who is doing it.

Some tips on what we had to fight with and what can be done. So I hope that helps guys. We'll see you next time.

The boys are replacing the cover for 1 head of mini split system they are installing.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Once you have the 5 and 12 pin in
00:30 The black connector does nothing for you
00:50 It's a little bit hard to do by yourself
01:30 Need to put the metal cover back on
01:45 Need to make sure the wires are in the little hole
02:20 Put all the screws back in
02:40 Now for the hard part
03:35 There you go

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#WiringMiniSplit #Electrical #DIYInstall

Transcript:
Once you’ve got your five pin and I think it’s a 12 pin, you have to put your cover back on. But you can't because the wires obstruct. We’ve got the fan on going right now. Everything is working. If everything works correctly this black connector does nothing for you. So what you have got to do is you got to remove this little hook here goes into a screw. The screws have a tendency to want to stick but they’ll fall out eventually, just take them out.

It's a little bit hard to do by yourself. Trust me. I know. Especially put it back up, getting it down is pretty easy. That one was sticky. All right. Let’s move this out of the way.

Now we got to put our metal cover back on. The thing with the metal cover. Firstly, you don't want to shock yourself, but we got to make sure these wire this whole is right. What I do is put it like that. Put a screw on it with a screw gun. And you put all your screws back in. Remember this one over here. There’s one right here. Get the other screw.

Now, the hard part of the easy part, believe it or not. It’s really hard to get this. You got to use both your hands. You got to use a screw gun. It might be easier for a screwdriver. Hold it up there, find your hole. By yourself it’d be really hard. There you go, now just hook it up like we showed you. Don't worry about this wire.

There you go.

Easy way to prevent wasps from making nests in the wiring of your mini-split. Something that not all AC guys do.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Recommended to do when you're wiring the mini split
00:25 Half inch connector
00:40 Idea is to keep wasps out
00:55 Take one wire at a time and fish it through
01:25 Slide the wire down to the black

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#WiringMiniSplit #Electrical #DIYInstall

Transcript:
All right. So one of the things that you don’t have to do, but it's recommended you do actually, I don't think a lot of AC guys actually do this, but it helps a lot. So there are I think this is a half inch connector that we'll put in this hole, like that. We’ll run this wire, this other wire through it. And I’ll show you guys, how we do that.

And the whole idea is keep wasps out. Right? So any time anyone has come out here and service it they don't have to... And weather. Deal with wasps getting on them, stinging them. So what we'll do is we'll take one of the wires at a time fish it through. Hold it upside down like that so that the gate doesn't keep falling on you. And you’ll fish them through one at a time, which it’s a little bit difficult.

Can be a little hard sometimes, and keep doing it. This will be the last one we’ve got to get through here. Just like that. We’ll slide it down to the black. Oh, there we go. And we're going to slide this in there and then you'll fit your little wing nut that comes with it. Going to put that on. You'll go down to it and you’ll tighten it on. I think I have mine on upside down. There we go. We're done.

That's how you do it. Keep bugs out. Look right here. No wasps can get up in that hole with that wire.

The boys are wiring up one of the heads for the 3-headed mini split system they are installing. You always want to install the highest capacity head on the a-lines.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Outside at the unit
00:25 Lines for outside power
00:35 This is for the highest capacity head
01:00 1B, 2B, 3B will be the second highest capacity
01:10 How they wired each head
02:00 Vacuum pump, how many microns to vacuum to
02:25 After you get to pressure, let it sit for like 15 mins
02:45 You can't use an analog gauge, won't tell the microns accurately
03:05 Can get the gauge set on Amazon for like $100
03:25 You will need to vacuum each head down

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#WiringMiniSplit #Electrical #DIYInstall

Transcript:
All right, guys, we're out here. We already got the inside hooked up like we were talking about. So look here. There's these three right here. L1, L2 and ground. That will be your power that comes in from outside. Into the unit. 1A, 2A, 3A is what's going out to your first head. What should be the highest capacity you have? All these heads here are all the same capacity, so we don't have to worry about that.

So if you have one that’s say 12,000 BTU and these are all 9000, you're 12,000 would be your first head on your unit, which would be here and then your lessers would be there. So your max-, your highest capacity of your first one, the one B to be three B will be your second one, 1C, 2C, 3C will be a third one.

So in our case, 1B, 2B and 3B will be our kitchen. 1C, 2C and 3C will be the living room for us. And we're not using all three of these. Well, one of the how the L1, L2 and the ground are the power coming in. So and then your ground, it has a connector around cracker here you'll have to one of these grounds here and square and there and that's how you do it.

But before we go, this is our old vacuum pump from Harbor Freight, still kicking. up here. When we vacuum down, we vacuum on the 500 microns is what you want to do, which is 29, 30 to 30 negative inches of mercury, which is an AC into the mercury. This one tells us a percentage. It’s a digital manifold gauge. So we're only 22% for this and we need to be at 100, which will be 30 inches a mercury, -30 inches of mercury.

And then what you'll do is you let it sit for like 15 minutes after you do that and you'll see where it is drop, how much is drop? And if you have a big drop, you have a leak. The issue is

Phil explains what you need to watch for when ordering a tub for your mobile home.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Replacing a mobile home bathtub
00:29 What you need to know for ordering
01:00 Going to take the tub and surround out to check the floor-there will be damage
01:24 Follow us

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#MobileHomeRepair, #MobileHomeImprovement, #DIYHomeRepair

Transcript:
Glad to have you here. We're going to travel to this little project. And this is replacing the bathtub, which has a center drain. We're going to turn it to the left-hand drain. which when you face the tub, the drains on the left or the drains on the right. That's how you order. Now, this is not a regular 60 inch tub.

It's smaller, so you have to get that size, which I think is 54 inches. And again, your tub surround would have to be to be one, not one that will shrink down to 54 on the back side. So keep that in mind when you go to get your tub location of the drain the size of the tub and then the surround.

So, we're going to take all this out. We'll see what we got to repair under the floor. If you notice it patched up all the fiberglass and it didn't hold. If you watch some of my other videos, you'll know why generally that means the floor is bad underneath and we'll have to get plywood and fix all that. But this is what we're doing.

We're taking it apart

This is the second part of how to change and drywall finish batten strips in your mobile home.

All on the journey to get your mobile home, more home-like.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:11 How to take off batten strips and hammer down nails
00:21 Take your drywall mud and put it on
00:53 Lay your tape right on top of the crack
01:46 There's your first coat of drywall mud
02:30 Bust out one side, then your other
03:00 He puts on with one size knife and then pulls off with bigger knife
03:25 It's a learned skill don't feel bad if takes you longer.

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#MobileHomeRepair, #MobileHomeImprovement, #BattenStrips

Transcript:
So remember, I showed you guys to take off the batten strips and then hammer down the nails and staples that are standing up around your hammer down. Then you take your drywall mud and you put it on. You can do it that way, or you can do it this way.

You want to make sure you get enough mud to cover. And then that if you down, the tape will blister up when you put mud on top of it later. Which you'll do a second coat. Lay it right on top of where that crack is.

I know I'm making it look easy, but I've done it for a long time and I just can't help it. Perhaps we'll show you guys how to do the drywall finishing it. It's not something you can learn overnight if it is. Then I've been pretty stupid because it took me a long time to get any kind of good. So anyway, you pull that down. Tight as you can. There's your first coat and then we'll finish it out, which I'll do is I'll put mud on like so if you just have a six-inch knife, you can do it with a six-inch. But I prefer to burst out with a ten and then a twelve. Then you spread it out.

But. Got to do one side. So that the knife will be able to cover when you go over it, like so. Do the other side know a lot of guys won't do but one side at a time? I understand.

But I can do both sides so and I don't I'm very much sanding. I don't do any sand as a rule. And normally, I put it on with a one size knife, and then I use a bigger knife, like if I put on with the six, I would pull it off with an eight-inch knife.

But you don't have to do both sides, you can do one side of everything, come back a bit after drys and do the other side, but there they'll be pretty flat. And then you just do that everywhere. Now I imagine that other people will have to work at it longer and don't feel bad.

That's part of it. But w

Several quick tips and tricks about drywall corner bead.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Back, sweaty, to show some of the things about corner bead
00:25 Want to cut your corner bead, it has a profile
00:47 Make sure you don't have anything bulged out to make an issue
01:15 Ways you can secure the corner bead.
01:30 Ways to keep corner bead straight
01:55 Want to get it tight and where it stands up
02:05 Want corner to be the high on both sides
03:07 Reason he uses screws
03:40 Aim is to always be a bit better and look after the customer
04:38 Follow us

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#drywall, #drywallcorners, #drywallcornerbeadtips

Transcript:
We're back. Caught me when I'm sweaty. Which is not ever, ever, I should be a supervisor by now, but I'm not. Anyway, we're doing a corner bead, want to show you how, things that I know about corner bead, some of the things I know. First of all your want to cut your corner bead, so you know it has a profile, if you notice it's built up off of each side so you can slide mud over the top of that. It's particularly, I want to show you. I want to sure you don't have anything that's going to keep you bulged out and make an issue.

And then you put it up here with this case for you to screw a one of the videos I showed you a corner bead clincher. You can do that. And you can also use nails, a lot of guys like nails. The thing about screws is that you want to make sure you don't pull so far down, that it will twist the metal you want to try to keep it straight.

So, try to eyeball it straight. And one of the ways you can kind of avoid doing that is put where you put one screw, put another screw over here, close. Now, you can use these holes or you can use the smaller holes, either way you want. The idea is to get it where it's tight and where it stands up. Now, you can twist it around and then this will be hidden When you go across instead of this, what you want is that corner to be the high on both sides All right.

So we're going to keep on going. Now, the reason I use screws as opposed to nails. It's a lot harder to knock that off, with a piece of furniture or something else.

And, you can always change something I was checking something, you can always pull screw out. It's harder to pull a nail out. And it's easier to knock a nail off, or for a nail to have vibration and pull out. I'm not saying you shouldn't do it with nails, I'm saying that's the reason

Phil shows you how to quickly remove the batten strips on your mobile home.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:11 Batten strips in mobile home
00:30 If it has paint want to cut either side then pull off with pry bar
00:45 Run your hammer and when hit nail pound it down.
01:05 Then you'll drywall finish it.

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#MobileHomeRepair, #MobileHomeImprovement, #BattenStrips

Transcript:
This is a common way to cover the strips. I mean, the cracks in the drywall, so, they put. This is called a batten strip, and they staple it on. Now if you want to get rid of that funny look that makes it look less like a house is you would you would.

If you have it painted a bunch, you're going to want to take a razor and cut on both sides. Otherwise it'll peel back the paint quite a ways. But you take a pry bar. Pull it off. And then just run your hammer.

And when you feel that bump, hammer it down. Then you'll dry, drywall finish it, and I'll show you that here in just a second. But that's what you do.

The boys are wiring up one of the heads for the 3-headed mini split system they are installing.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Boss ran into town to get some supplies
00:20 Ran wires from the outside unit
00:40 Thing that took a minute to figure out
00:55 The black 5 pin doesn't connect to anything
01:20 Connects right there
02:20 Just push it out with a screw driver
02:35 How you need to run the wire to plug it in
03:00 On the other side with the wires, you could snip them if needed
03:25 By the manual instructions
03:40 Make sure it's hooked up the same on both sides
04:40 Make sure the electricity is OFF
05:05 The colors need to correspond to what you did out at the unit
06:45 What it looks like up close
07:10 Hooking up the 5-pin
07:35 Installing the cover

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#WiringMiniSplit #Electrical #DIYInstall

Phil's showing and explaining what you need to consider when installing the copper lines for an air conditioner.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Ran the copper insulated line
00:35 Adjust them very slowly, don't kink them
00:46 Do not try to start them with a pair of wrenches
01:20 Shaped the lines to be against the wall, and will build something to cover them
01:35 Have 2 more 50' runs
01:50 You can install this for yourself with little or no experience
02:00 You can't get the extra freon for anything beyond 25'
02:15 It has in it the ability to deal with 25' runs

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#AirConditioner #CopperLines #InstallingAirConditioner

Transcript:
So what we've done is run this line that's already got its insulation. And both this little area right here is where we tore the two apart to have a way to hold them together. Obviously, they can't be the same together because they have one set back from the other.

We went through the first 25 footer on the a and you start these you adjust them very slowly. Don’t kink them. That's a bad thing to kink copper and then you start over hand until they're on their good Do not try to start them with a pair of wrenches or something because you can end up stripping it. That's bad too.

Really bad. So take the time to shape the pipe so that you can put that on my hand almost all the way. You can usually do it. Then you can tighten it up with a crescent wrench or it's a three quarter size and this is three quarter. And I think this one's going to be like inch and a quarter.

I haven't tried it. So we used crescent wrench to set this on. Then I shaped in so that it would be up against the wall, will end up building up a wall to hide it wrap it up in, so bugs won't land on it and make nests on it, all that kind of stuff. And it will tend to blend in, but we still have two more runs.

Both of those are 50 foot and then we'll I'm not showing you up there because I'm letting Drew do it, tightening it up. But it's not something that's impossible to do for somebody who doesn't have the experience. So that's why I'm telling you with quiet comfort that you can do this yourself. Now, you can't get the freedom, you don't have the gauges.

So when you go to 50 foot or anything beyond 25 foot per run, you will have to have somebody add freon to it .16 ounces per one foot past 25. Ok, It has it in it the ability to deal with 25 feet per run. After that, you have to add freon and we'll have to see how that all goes.

I'll let you know as we go along. Right now, he's up in the attic getting sweaty just like me. See you in a bit.

The home repair and construction trades are blowing up cost wise. Phil explains what some jobs cost to do versus the profit. Don't be mad at the repair person, unless they own the company the money is going into the boss's pocket.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 The mini-splits using flare fittings is probably why you're seeing expensive flare tools
00:25 AC guys are making so much money
00:45 So are electricians and plumbers
01:15 Will you have to deal with it? Depends.
01:30 You're paying for their skill and willingness to do the dirty job
01:45 The guys doing the work, the techs don't make that much
02:25 Cost breakdown for an AC
03:10 Plumbers and a water heater cost break down
03:40 The trades will be making the big bucks in the future

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#plumbers #electricians #bizop

Transcript:
Which is probably why now all of a sudden there's this real fancy automatic $300 flare tool, available online because the air conditioning guys are making so much money that they can afford to buy platinum covered, they'll be something there'll be a 2 to $3000 flaring tool come out. They'll massage your back while you're doing it. You put it on like a armor thing. Believe me, these guys are making way too much money.

But so are electricians and plumbers. The those guys don't. They buy big buildings and fancy trucks and I believe too greedy. And then all the inspectors are all kind of their buddies, you know, even though they fail them from time to time because they all believe in having high end stuff done. Is it necessary? No. Are you going to deal with it?

Yes. You’ll have to deal with it. The fact that you know, that they're ripping you off. That don't make you feel better that they're making a huge, exorbitant amount of money that doesn't make you better either. But you don't. You didn't go through the route of learning how to be an air conditioned guy or a plumber or elect... electrician. You learn to do something else.

So that's the choices that they have now. By the way, the guys who do the actual work, they don't get paid that much. They don't get paid as much as a dump truck driver generally. Unless you live in a union town or state. They don't get paid that much. The owner, that’s who gets paid. So you really have to learn about air conditioning and then become an owner in order to make the money that they're making for the company.

So don't be so mad at the technician wh

We're wiring up the Pioneer Inverter Ultra High Efficiency Heat Pump 3 head mini split.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Pioneer Mini split
00:30 Made in China designed in Japan
00:45 Efficiency rating
01:00 Not real heating efficient
01:15 This is 21-23, most units are 16-18
01:35 Checking to see if they have the fittings needed
02:10 They'll have to move the disconnect because of where the customer wants the unit
03:10 Where the power will be going in
03:35 If you look inside here
03:45 Comes with flare fittings on it
05:40 Quick rundown of what you need
06:45 He has to go get a flaring tool, checking for anything else he needs to buy
07:45 Had to order 2 50' lines
08:00 The instructions are in geek speak
08:20 Freon needed per 25' past the what's already in there
08:45 As simply as he can make it for the extra freon needed
09:00 Reason why new fancy $300 automatic flare tool

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#airconditioner #howtowire #wiringminisplit

I need a razor knife. They’re all wearing shorts. I'm wearing pants. And guess what, I'm the one that has all the stuff on and can squat down, get dirty, and not worry about my knees. I have cargo shorts. Right, but I'm the one that has all the stuff.

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#MobileHomeRepair, #MobileHomeImprovement, #DIYHomeRepair

We're installing another head for the mini-split ac. Pioneer Inverter Ultra High Efficiency Heat Pump 3 head mini split.

Where this head is going: tongue-and-groove ceiling, metal roof of the original mobile home. Then you have the roof that covers the old mobile home and all the additions. Not something most will run into, but maybe it will help you out.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Bit of a unique situation
00:30 Cut out the tongue-and-groove ceiling to put in the cassette head
00:40 This is a three head mini split system, each head has been a unique install
01:10 Don't know if they will run into rafters on top of the metal roof
01:25 Use a Sawzall to cut through the original metal roof
02:10 The old mobile home roof
02:50 The rafters lined up
03:05 Pulling the insulation out of the way
03:30 Your freon lines will cause problems with the hole
03:50 Have to cut out the area for the lines
04:10 They have set the hangers
04:25 That's why we have turned these
04:50 Takes 2 people to set the head, have cut a 7/8" piece to guide from the ceiling
05:00 It's kind of awkward for one person to be holding it while the other screws it above
05:30 Setting the cassette head
06:35 Installing the cover, make sure to line up the wires
08:10 Will end up doing the wiring and we'll show you when we do

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#minisplit #ACInstall #cuttingceiling

Worried about the red light in a bathroom vent? Phil takes one apart to show you what it is.

Evidently, I didn't know there's a complaint on people that rent Airbnb is and such that there are lights pointing to the maybe that somebody is watching them. So if you look up here, you see this red light. Let’s look and see if that's a camera.

Now, you see that right there? That's not a camera. And the reason I know that is because I put this in. There is no camera in there. That is just something they decided to put in to let you know when you got power to it. So I want you guys to rest easy that there is no camera looking at you because there's a little red light there.

Nowadays, they have cameras that won’t have lights. So that doesn't make you feel better, I'm sure. But relax a little bit more. That's not a camera.

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#bathroomvents #isitacamera #redlightinvents

Need to check your bathroom exhaust fan? Worried about breaking things. Phil shows you how to pull it down without problems.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Wanting to get into your exhaust fan?
00:30 Worried about breaking things?
00:40 There's slots with clips that let it hang
00:55 You squeeze it together
01:20 Sometimes the motors go out or you need to clean

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#Exhaustvent #bathroomexhaustfan #openexhaustvent

Transcript:
Well, if you're wanting to get into your fan, in your exhaust fan for your bathroom slash, wherever there happens to be a fan that pulls out air mostly in the bathroom, you might not know how to get into that. And you might worry oh and pull in on it. It's doing weird feeling, it makes me feel insecure about maybe I'm going to break it.

You pull it down like so and see how it hangs there. If you look at it, there's some slots up in there and this spring type. So these things here, you have to squeeze them together and it keeps it from pulling all the way out of that round part right there. So you squeeze it together and it comes out and you see the slots in there on both sides.

This is where the screws are. But right here, you want to push that together like so. Same with this one. Push it together, and then this. Hang in there again. Now you slide it just to flip. Then you can look in there, see if the fan sometimes the fan motors go out and you can replace those fan motors.

Sometimes you just might want to clean in there. I've seen it where they're pretty full of spider nests and webs, all kinds of stuff. So if you want to get up into your exhaust, your exhaust fan in your bathroom, that's how you do it.

Worried about the red light in a bathroom vent? Phil takes one apart to show you what it is.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 The twins let us know that people have concerns about that
00:25 This is a fan to pull out smells and moisture
00:45 What that light actually is
01:00 He knows because he installed this
01:20 You can relax a little bit more at your Air BNB
01:33 Most cameras now...

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#bathroomvents #isitacamera #redlightinvents

Transcript:
I was told by my boys who were younger than me and probably more in touch with the younger generation or what's going on. Tick tock. But there are some worry about red lights in vents, particularly in the bathroom. This is a fan to pull out the smells and the moisture and there's a light and there's a red light in there. So that might make you think that somebody's spying on you. So let's take a look.

Now, that is just a light, not a camera. There's a light to let you know this thing has power to it. So if the fan goes out, how do I know that? Because I installed this. There is no there is no camera. See... Is that a switch. See, now the power’s off okay. So I want you to relax a little bit more when you're on your vacation, Airbnb or whatever you're doing it for, because that's definitely not a camera.

Phil explains what's happening when you flush one toilet and another bubbles.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Flushing the other toilet in the house
00:35 Have a vent that's not working

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#toiletbubbles #toiletbubbleswhenshowerdrains #toiletproblems

Transcript:
Ok Drew. I don't think he heard us. Go ahead and flush it, Drew. That is us flushing the other toilet in the house. And the air's coming up here. So that means we have a vent that is not working. Now we're on the hunt for a vent that is blocked.

All right. Just let you know when you start seeing that bubbling anywhere else, you got a vent that's not working. So keep that in mind.

Using Drano Max gel pro strength to put in the toilet. It’s the first time for this is an 80 oz value size for one fifth of it, or 20% of this in there, which we've done. And now we're going to put this to the test.

I am not having it.

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#DranoMaxGel, #Draino #pluggedtoilet

Ok Drew. I don't think he heard us. Go ahead and flush it, Drew. That is us flushing the other toilet in the house. And the air's coming up here. So that means we have a vent that is not working. Now we're on the hunt for a vent that is blocked.

All right. Just let you know when you start seeing that bubbling anywhere else, you got a vent that's not working. So keep that in mind.

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#toiletbubbles #toiletbubbleswhenshowerdrains #toiletproblems

So now we did the 20% in 20 minutes or so and it didn't do the job. So we went and poured all of it in it and it did the job. So maybe you ought to spend $12 and get it, pour it all in.

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#DranoMaxGel #StoppedUpToilet #PluggedToilet

Will the Drano Max Gel work like the tell you to do it?

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Clogged toilet
00:25 We're going to try Draino Max
00:40 Let it sit for a while
00:50 Gave it a lot of time, but no luck
01:15 Would rather have the liquid fire
01:30 Poured the whole bottle in there and it went ahead and did the work.

🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf

➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf

➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair

#DranoMaxGel #StoppedUpToilet #PluggedToilet

Transcript:
Do Vanna White. This is not a Vanna White situation in the toilet. The is plugged up and we have some Drano, Max, we're going to try. This time last time we did Liquid Fire, which I’ve had success with and it says to pour a fifth of the bottle. And we're going to give it a shot. It is not what you normally put in a toilet. And then we're going to let it sit for a while and see what happens. We'll come back to you then.

So we gave it a lot of time. And this Drano pro strength max gel didn’t do the job even though you're not... Supposed to. You’re not supposed to put it in the toilet. It's been done. It does work, you know, for other people. But not in this case, it didn’t, and now I've got to deal with all this excess water and maybe the plunger and the Draino together. Here I am, I’d rather have the liquid fire. See you guys.

Took 20%. Let us sit for 20 minutes. Didn't make any difference. We poured the whole bottle in there. It went ahead and did the work. So maybe you ought to pour the whole bottle. Just to let you know, if you want to spend $12 to do that, then there you go. See you.

Phil's installing a 3 headed mini split air conditioner for a customer. Here they are completely installing one of the cassette heads.

Pioneer Inverter Ultra High Efficiency Heat Pump 3 head mini split.

⏱️⏱️Chapters⏱️⏱️
00:00 Intro
00:12 Installing a 3 headed mini-split
00:25 One of the heads will be going through a double ceiling
00:45 Took a drill and bit and drilled out the corners where we need to cut
01:05 Went upstairs to mark the plywood
01:45 Made the cut marks
02:15 Going to cut the drywall
02:40 Back after pulling the drywall out
02:50 Scored the drywall with razor knife and cut with an oscillating saw
03:08 Put a paddle bit wider that the saw blade and drill the corners
04:00 Something you may run into when measuring
04:15 The jog in the hole is for the freon lines
04:35 Before cutting, make sure there's no electrical above you
04:45 They ran into that with one of the heads
04:55 The instructions are for offices, not good for putting in a house
05:13 This job has several complications. They have to adjust to.
03:20 Cutting the plywood
06:10 Be careful of falling debris
06:25 Need to move insulation back... The heat is flooding into the room
06:50 Put boards to support the area
07:20 The area for your freon lines you'll have to support too
08:00 Pattern for the shape of the head
08:25 The pattern shows a gap, you're not going to have it when it comes to rafters
08:45 They are doing the second head
08:55 Where the control wires go
09:50 Installation manual, pretty specific for acoustical ceiling
10:05 He's showing you how to put it into a home
10:20 The supports are in the blue package
10:50 The drain and freon lines for the head
11:05 Where the lines will be pointing
11:30 Electrical will come in there. You're using a 5/8 wrench
12:00 Installing the support bars
14:25 You have to keep an eye on the support to make sure it's facing where you need it to
15:00 2 supports are done
15:45 Want to be careful when rolling the head over
16:10 Leave enough room on the bottom to adjust it if you have to
16:50 The kit has anchors for concrete
17:30 You could use the anchors if it was inside a wall, but probably won't need them
18:00 Cut a piece of wood to keep the head 7/8 above the ceiling
18:20 Using 1/4" roofing screws
18:52 Not really a one person job trying to get the head up there
19:10 Woops, cut the area wrong
19:20 Need to cut the other corner out
19:45 Had to move the freon lines and cut another hole
20:00 You can't have the freon lines going out, may have to adjust
21:00 Using roofing screws to fasten it
21:45 The fun of working with someone you can't see
23:00 Only thing stays same is everything changes
23:10 Heavy or awkward?
24:50 The small piece of board is a measuring device
26:10 The box for the cassette head cover
26:50 Little tiny package of screws in the box
27:10 The cover doesn't go on just any old way
27:35 The wires have to go to a specific space
27:45 Where the wires have to go
28:25 To put the screws in you have to take