Simple Hack To Help Plane 8 Quarter 9 Foot Lumber In A Small Shop. we use our 6 foot level to act as a rail for planeing 9 foot lumber, it helps eliminate snipe .

it just happens to be the exact height we needed when we clamped it to our work table. so no more holding it with our hands and hoping we can keep it level enough , and some boards that size get pretty heavy.

Simple Hack To Help Plane 8 Quarter 9 Foot Lumber In A Small Shop. we use our 6 foot level to act as a rail for planeing 9 foot lumber, it helps eliminate snipe .

it just happens to be the exact height we needed when we clamped it to our work table. so no more holding it with our hands and hoping we can keep it level enough , and some boards that size get pretty heavy.

Went to our buddies to grab our Walnut order that got delivered to his shop , he grabbed it with his Kubota SSV 75 skid steer , man Lumber is getting expensive. this load cost just over $1800 . it's just over 100 board feet.

thanks for watching

Hello Everyone, in this video, we are doing a Celtic style shield engrave , we are using 3/4 inch ply painted black. this is going to be a shop wall hanger , we recently did maintenance to our cnc and flattened the waste board , so this was to see if the V-Carve was nice and even , and it was , finally 😀

Machine - Shapeoko 3 XXL
Thanks for watching

Ways to support the channel

Check out our Online store
https://www.thealexanderbroswoodworking.com/our-store

Support the channel
https://www.paypal.com/donate/?hosted_button_id=RGAHQ9VLYB49E

#woodworking #cnc #test
Hello everyone , Matt Here from the Alexander Bros Woodworking , In todays video I am Doing what is hopefully the last test engrave for this sign we are doing for a local motorcycle club . The other tests we did were way too deep and looked like garbage .

We are using 3/4 maple plywood painted black so we can see the contrast from the carve . We are using a 1/8th bit to pocket out the majority of the material and follow up with a 1/4 60 degree Vee bit for the rest .

Machine - Shapeoko 3 XXL
Thanks for watching

Ways to support the channel

Check out our Online store
https://www.thealexanderbroswoodworking.com/our-store

Support the channel
https://www.paypal.com/donate/?hosted_button_id=RGAHQ9VLYB49E

We are trying to dial in the depth for this local motorcycle clubs sign .
we are having an issue where the depth we set in the programming is different from the outcome , and we think the CNC is not running flat , as we know the bed waste board is flat , going to have to do more adjustment's I think , thanks for watching

Check out our Online store https://www.thealexanderbroswoodworking.com/our-store

Support the channel
https://www.paypal.com/donate/?hosted_button_id=RGAHQ9VLYB49E

added some copper colored epoxy to this slab to fill in holes and cracks , and man there was lots of micro cracks.

Sanding off copper colored epoxy off a walnut slab ,that we are making into a breakfast nook shelf for a client

We have a lot of scrap wood we had glued up into cutting board blanks that were too thin or too small , so we decided to cut them up and make end grain cutting boards.

Check out our Online store
https://www.thealexanderbroswoodworking.com/our-store

Support the channel
https://www.paypal.com/donate/?hosted_button_id=RGAHQ9VLYB49E

This is part 2 of the shop sign . here we clear it , to seal it before painting it black , then sand it off #woodworking #wood #sandingmachine

Ways to support the channel

Check out our Online store
https://www.thealexanderbroswoodworking.com/our-store

Support the channel
https://www.paypal.com/donate/?hosted_button_id=RGAHQ9VLYB49E

#woodworking #wood #cnc
Hello everyone, in this video we are carving a new sign for our shop , we are using our Shapeoko 3 XXL .
The wood we chose was Cherry as we find it carves very nice . the carve in total was 3.5 hours.
this is a edited version of the livestream

Ways to support the channel

Check out our Online store
https://www.thealexanderbroswoodworking.com/our-store

Support the channel
https://www.paypal.com/donate/?hosted_button_id=RGAHQ9VLYB49E

We are carving our new logo for a shop sign on our shapeoko 3 XXL cnc
we are using cherry lumber , sign is 12x12 ( pocketed area )
#woodworking #cnc #logo

#woodworking
We visited our buddy Nathan today ,we sanded up some slabs using his Felder FW 950 Wide Belt Sander. The 2 slabs are a table top that we are refinishing and flattening for a client

Check out our Online store
https://www.thealexanderbroswoodworking.com/our-store

Support the channel
https://www.paypal.com/donate/?hosted_button_id=RGAHQ9VLYB49E

While visiting our buddies woodshop he showed us his new toy. The OMEC 650A Dovetail Machine, and boy oh boy it is fast and so much easier.

Check out our Online store https://www.thealexanderbroswoodworking.com/our-store

Support the channel
https://www.paypal.com/donate/?hosted_button_id=RGAHQ9VLYB49E