TheRogueBanshee

Our 5D Tactical video will show you what comes with the 5D Tactical Multiplatform jig and how to use it.

We have an article that we put the 80 Percent Arms Jig against the 5D Tactical Jig. Visit that article at https://trb.fyi/ar-jig-shootout-5d-tactical-vs-80-percent-arms

The lowest advertised price that we found on the Internet is from JSD Supply. Check out the jig here https://bit.ly/373D8aL

Visit us at : 

http://www.trb.fyi
http://www.facebook.com/TheRogueBanshee/
http://www.twitter.com/TheRogueBanshee
http://www.patreon.com/TheRogueBanshee  

Video Index:

What comes with the jig kit - 0:24
Step 1: Installing the buffer adapter - 2:13
Step 2: Mounting the lower to the jig - 3:16
Step 3: Installing the side plates - 5:06
Step 4: Installing the drill guide - 6:20
Step 5: Router setup - 7:02
Step 6: Drilling the pilot hole - 9:07
Step 7: Milling the lower - 10:31
Step 8: Drilling the safety, hammer and trigger pin holes - 13:58
Step 9: Removing the receiver from the jig - 14:59
Does it work - 15:48

Visit our 5D Tactical - Tools used in our video article on www.trb.fyi to learn more about the tools we used in this video. Each tool will have a link to get to the product, helping you shop more efficiently while supporting our work.

If you like the work that we do at The Rogue Banshee, please consider supporting us for free by clicking on our affiliate links before purchasing gear, parts and tools, donating to us using the links to the right of this article or becoming a patron on Patreon. Your support helps us produce content as we do not allow vendors or manufacturers to pay us for content. 

Also, don't forget to share our content on your favorite social media platform by clicking the sharing buttons below.

The 4 pistol case by Cedar Mill Fine Firearms is a US made product that protects guns, gear and electronics from shock and water.

See what happens when we load this case up with 4 Sigs and throw it in a lake as well as drop it from 8 feet.

If you would like to know how I came about my recommendation visit my article named Adventures with the four pistol case from Cedar Mill Fine Firearmslocated at https://trb.fyi/adventures-with-the-four-pistol-case-from-cedar-mill-fine-firearms

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on gear and firearms. Also, remember to subscribe while you are there. 

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee

The Delta Kwik is a US made product that allows the rapid removal of the AR15 handguards that uses the typical slip ring (sometimes called delta ring) that is on standard ARs, M15s and M4s. In this video I show you how it works and share some of my thoughts.

If you would like to know how I came about my recommendation visit my article named Adventures with the Delta Kwik located at http://trb.fyi/adventures-with-the-delta-kwik

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content AR type firearms and remember to subscribe while you are there. Also, make sure to visit the Full30 Forum located at https://forum.full30.com/ to interact with other gun owners in some awesome conversations about all aspects of our sport. While you are there stop by my profile (https://forum.full30.com/u/TheRogueBanshee/) to see what threads that I am active in.

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee

We are developing the 80% AR Magazine. While this is still in development, we have produced a video showing you how the process will work.

We even have a solution for those in magazine restricted states.

Learn more at our website https://trb.fyi.

Thanks for watching our April Fools Day 2019 video. If you would like to see what tools we used in this video please visit https://trb.fyi/tools-used-in-the-80-ar-15-magazine-video/

Our Polymer80 PF940SC first shots and range testing video will show you the first shots of this completed 80% frame.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on Polmer80 products remember to subscribe while you are there. 

If you want to learn more about the tools used in the PF940SC Videos visit https://trb.fyi/tools-used-in-the-polymer80-pf940sc-completion-videos/. If you need more information about troubleshooting visit our Glock Troubleshooting Guide at https://trb.fyi/glock-troubleshooting-guide/
 

<B><P>Visit us at : </P></B>
 
<P>http://www.trb.fyi  
<P>http://www.facebook.com/TheRogueBanshee/  
<P>http://www.twitter.com/TheRogueBanshee  
<P>http://www.patreon.com/TheRogueBanshee

Our Fixing incorrectly drilled holes on a Polymer80 video will show you how to fill in holes that were incorrectly drilled into the frame.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content 80% firearms and remember to subscribe while you are there. Also, make sure to visit the Full30 Forum located at https://forum.full30.com/ to interact with other gun owners in some awesome conversations about all aspects of our sport. While you are there stop by my profile (https://forum.full30.com/u/TheRogueBanshee/) to see what threads that I am active in.

If you want to learn more about the tools used in the PF940SC Videos visit https://trb.fyi/tools-used-in-the-polymer80-pf940sc-completion-videos/. If you need more information about troubleshooting visit our Glock Troubleshooting Guide at https://trb.fyi/glock-troubleshooting-guide/
 
Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

Video Index

Background - 0:16
Filling in the oops - 0:57
Using a Dremel to clean up the frame - 2:31
Using a hobby knife to clean up the frame - 4:03
Final sanding of the frame - 5:51
Trim the inside - 7:16

Our fixing frame damage on a Polymer80 video will show you how to fill in the damage from a Dremel should it slip when cutting off the tabs.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on Polmer80 products remember to subscribe while you are there. 

If you want to learn more about the tools used in the PF940SC Videos visit https://trb.fyi/tools-used-in-the-polymer80-pf940sc-completion-videos/. If you need more information about troubleshooting visit our Glock Troubleshooting Guide at https://trb.fyi/glock-troubleshooting-guide/
 
Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

Video Index:

Background - 0:16
Filling in the oops - 0:57
Finishing the repair - 1:38

Our Polymer80 PF940SC completion using a drill press video will show you how to complete the Polymer80 subcompact frame using the included endmill and a drill press. We don't recommend that you complete the frame this way as you will see in the video. We recommend that you complete the frame using a Dremel. Visit our channel for the completion using a Dremel video.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content 80% firearms and remember to subscribe while you are there. Also, make sure to visit the Full30 Forum located at https://forum.full30.com/ to interact with other gun owners in some awesome conversations about all aspects of our sport. While you are there stop by my profile (https://forum.full30.com/u/TheRogueBanshee/) to see what threads that I am active in.

If you want to learn more about the tools used in the PF940SC Videos visit https://trb.fyi/tools-used-in-the-polymer80-pf940sc-completion-videos/. If you need more information about troubleshooting visit our Glock Troubleshooting Guide at https://trb.fyi/glock-troubleshooting-guide/

<B><P>Visit us at : </B>
 
<P>http://www.trb.fyi  
<P>http://www.facebook.com/TheRogueBanshee/  
<P>http://www.twitter.com/TheRogueBanshee  
<P>http://www.patreon.com/TheRogueBanshee  

<B><P>Video index:</B>

<P>Recommendation - 0:16
<P>What's included - 0:41
<P>Basic steps - 1:09
<P>Drilling the frame - 1:36
<P>Cutting the frame - 2:55
<P>Cutting the barrel block - 4:31
<P>Installing the magazine release - 7:19
<P>Installing the rails - 8:15
<P>Installing the trigger - 9:44
<P>Installing the takedown - 12:03
<P>Does it work? - 13:07

Polymer80 PF940SC completion using a Dremel

Our Polymer80 PF940SC completion using a Dremel video will show you how to complete the Polymer80 subcompact frame using a Dremel.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content 80% firearms and remember to subscribe while you are there. Also, make sure to visit the Full30 Forum located at https://forum.full30.com/ to interact with other gun owners in some awesome conversations about all aspects of our sport. While you are there stop by my profile (https://forum.full30.com/u/TheRogueBanshee/) to see what threads that I am active in.

If you want to learn more about the tools used in the PF940SC Videos visit https://trb.fyi/tools-used-in-the-polymer80-pf940sc-completion-videos/. If you need more information about troubleshooting visit our Glock Troubleshooting Guide at https://trb.fyi/glock-troubleshooting-guide/

<B><P>Visit us at : </B>
 
<P>http://www.trb.fyi  
<P>http://www.facebook.com/TheRogueBanshee/  
<P>http://www.twitter.com/TheRogueBanshee  
<P>http://www.patreon.com/TheRogueBanshee  

<B><P>Video index:</B>

<P>What's included - 0:16
<P>Basic steps - 0:44
<P>Drilling the frame - 1:12
<P>Cutting the frame - 2:30
<P>Cutting the barrel block - 4:05
<P>Installing the magazine release - 5:33
<P>Installing the rails - 6:29
<P>Installing the trigger - 7:57
<P>Installing the takedown - 10:16
<P>Does it work? - 11:21

80% Arms Easy Jig Gen 2 step by step AR 15 lower completion will show you how to use the Jig from 80% Arms to complete your lower.

There are multiple configurations to the 80% Arms Jig. This video features the AR15, however the process is similar for the 9mm and 308 versions.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content 80% firearms and remember to subscribe while you are there. Also, make sure to visit the Full30 Forum located at https://forum.full30.com/ to interact with other gun owners in some awesome conversations about all aspects of our sport. While you are there stop by my profile (https://forum.full30.com/u/TheRogueBanshee/) to see what threads that I am active in.

If you want to learn more about the tools used in the AR 15 Videos visit https://trb.fyi/tools-used-in-the-80-arms-ar15-jig-video If you need more information about troubleshooting visit our AR Troubleshooting Guide at http://trb.fyi/ar-15-troubleshooting-guide/

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

Video index:
What comes with the kit - 0:16
Assembling the jig around the lower - 1:07
Assembling the router - 3:57
Preparing the first hole - 5:31
Milling the lower - 6:30
Drilling the selector, trigger and hammer pin holes - 9:48
Removing the lower from the jig - 10:30
Does it work - 11:22

Our AR 15 bolt carrier group disassembly and reassembly video will show you how to disassemble and reassemble the AR 15 bolt carrier group.

This video features an AR 15 Rifle, however, the same procedures will work with an AR 10 with the exception of the bolt release which is a screw on an AR 10 where it is a roll pin on an AR 15.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on AR type firearms and remember to subscribe while you are there. 

If you want to learn more about the tools used in the AR 15 Videos visit http://trb.fyi/tools-used-in-the-ar-15-videos/ If you need more information about troubleshooting visit our AR Troubleshooting Guide at http://trb.fyi/ar-15-troubleshooting-guide/

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

Video index:
About the bolt carrier group - 0:16
Removing the firing pin - 0:35
Removing the bolt - 1:20
Disassembling the bolt - 2:19
Installing the ejector - 4:17
Installing the extractor - 5:44
Assembling the bolt carrier group - 6:49

Our AR 15 lower receiver assembly video will show you how to assemble your AR 15 from its individual components.

This video features an AR 15 Rifle, however, the same procedures will work with an AR 10 with the exception of the bolt release which is a screw on an AR 10 where it is a roll pin on an AR 15.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on AR type firearms and remember to subscribe while you are there. 

If you want to learn more about the tools used in the AR 15 Videos visit http://trb.fyi/tools-used-in-the-ar-15-videos/ If you need more information about troubleshooting visit our AR Troubleshooting Guide at http://trb.fyi/ar-15-troubleshooting-guide/

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

Video index:
Installing the bolt catch - 0:34
Installing the trigger guard - 2:57
Installing the rear takedown pin - 4:08
Assembling the collapsible stock - 5:35
Installing a collapsible stock - 7:08
Installing an A2 stock - 10:13
Installing the front takedown pin - 12:18
Installing the magazine catch - 13:45
Installing the trigger spring - 15:15
Installing the trigger - 16:21
Installing the selector and pistol grip - 18:05
Installing the hammer spring - 20:03
Installing the hammer - 20:29
Installing the buffer and buffer tube - 22:11
Does it work? - 22:56

Our AR 15 Field Strip Video will show you how to Field Strip for cleaning and routine maintenance. Field stripping an AR is essentially opening up the rifle and removing the bolt carrier group. In our AR 15 upper disassembly video we will disassemble the bolt carrier group. Later in our AR 15 upper reassembly video we will reassembly the bolt carrier group.

This video features an AR 15 rifle, however, this process will also work for the AR 10 rifle as well.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on AR type firearms and remember to subscribe while you are there. 

If you want to learn more about the tools used in the AR 15 Videos visit http://trb.fyi/tools-used-in-the-ar-15-videos/ If you need more information about troubleshooting visit our AR Troubleshooting Guide at http://trb.fyi/ar-15-troubleshooting-guide/

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

Video index:

History - 0:35
Checking for an unloaded firearm - 1:25
Removing the bolt carrier group - 3:00
Installing the Bolt carrier group - 4:02

Our AR 15 lower receiver disassembly video will show you how to disassemble your AR 15 lower down to its individual components. Watch our AR 15 Lower Reassembly Video to learn how to put it back together again.

This video features an AR 15 Rifle, however, the same procedures will work with an AR 10 with the exception of the bolt bolt which is a screw on an AR 10 where it is a roll pin on an AR 15.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on AR type firearms and remember to subscribe while you are there. 

If you want to learn more about the tools used in the AR 15 Videos visit http://trb.fyi/tools-used-in-the-ar-15-videos/ If you need more information about troubleshooting visit our AR Troubleshooting Guide at http://trb.fyi/ar-15-troubleshooting-guide/

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

Video index:
Checking for an unloaded firearm - 0:35
Removing upper receiver - 2:10
Removing the buffer and buffer spring- 3:17
Removing the magazine catch - 3:52
Removing the Pistol Grip and Selector - 4:45
Removing the hammer and trigger - 6:26
Removing the front takedown pin - 8:54
Removing a collapsible stock and buffer tube - 10:11
Removing an A2 stock and buffer tube - 11:52
Removing the rear takedown pin - 13:44
Disassembling the collapsible stock - 14:22
Removing the trigger guard - 15:23
Removing the bolt catch - 16:39

Our The Reckoning by CrossBreed Holsters video will show you the opening of the package that we received from CrossBreed. Then walk you through adding tension to the trigger guard as well as changing the holster from inside the waistband (IWB) to outside the waistband (OWB) and then back again. Finally, we will explore the possibility of using this holster with the subcompact configuration of a P320 even though this holster was designed for the compact or carry configuration.

This holster was provided to us for free by CrossBreed however there are no opinions in this video. To see what we think about this holster visit www.trb.fyi/adventures-with-the-reckoning-holster-by-crossbreed

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on Sig Sauer firearms and remember to subscribe while you are there. 

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

 
Video Index: 
The Opening - 0:40
Checking for an unloaded firearm - 2:09
Does it fit? - 2:28
Adding tension to the trigger guard - 2:49
Changing from IWB to OWB - 3:58
Changing from OWB to IWB - 11:24
Does it work with the subcompact P320 - 18:11

Our P320 80% Range Testing Video will show you the first shots of the build, as well as some, follow up work we completed.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on Sig Sauer firearms and remember to subscribe while you are there. 

For the tools that we used on the Sig P320 videos visit http://trb.fyi/tools-used-in-the-p320-disassembly-and-reassembly-videos and visit our troubleshooting guides at http://trb.fyi/troubleshooting/ while you are at our page.

Visit us at : 

http://www.trb.fyi

http://www.facebook.com/TheRogueBanshee/

http://www.twitter.com/TheRogueBanshee

http://www.patreon.com/TheRogueBanshee

Video Index: 

First Shots – 0:40

Load Three and Test Fire – 1:05

Load More and Test Fire – 1:15

Change Caliber to .40 and Test Fire – 1:46

Post Firing Inspection of the FCU - 2:12

Cleaning sharp edges and polishing the FCU – 4:07

Our P320 80% Parts Kit Install Video will walk you through installing your lower parts kit into your completed MUP-1 80% Frame. This is a follow-on video to our P320 80% Frame Completion

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on Sig Sauer firearms and remember to subscribe while you are there. 

For the tools that we used on the Sig P320 videos visit http://trb.fyi/tools-used-in-the-p320-disassembly-and-reassembly-videos and visit our troubleshooting guides at http://trb.fyi/troubleshooting/ while you are at our page.

I would like to thank switchpod (https://forum.full30.com/u/switchpod/) on the Full30 Forum for doing an excellent explanation of how to calculate drill speeds.

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

 
Video Index: 
Assembling the Safety Lever Housing – 0:32
Installing the Safety Lever Housing – 1:03
Installing the Safety Lifter and Sear – 2:19
Installing the Takedown Safety Lever – 5:00
Installing the Trigger Bar and Trigger - 6:09
Installing the Slide Catch Lever – 7:17
Does it work? – 8:19

Our P320 80% Frame Completion Video will walk you through completing the MUP-1 80% Frame.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on Sig Sauer firearms and remember to subscribe while you are there. 

For the tools that we used on the Sig P320 videos visit http://trb.fyi/tools-used-in-the-p320-disassembly-and-reassembly-videos and visit our troubleshooting guides at http://trb.fyi/troubleshooting/ while you are at our page.

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

 
Video Index: 
Inserting the Frame into the Jig - 0:32
Bending the Frame Rails - 1:55
Drilling the Holes - 3:47
Opening up the Trigger Slot - 5:48
Opening up the Safety Lever Slot - 6:55
Cutting the Slide Rails - 8:35
Deburring the Frame - 13:15

Our P320 FCU Disassembly and Reassembly Video will walk you through disassembling the Fire Control Unit down to its individual components and then put it back together again.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on Sig Sauer firearms and remember to subscribe while you are there. 

For the tools that we used on the Sig P320 videos visit http://trb.fyi/tools-used-in-the-p320-disassembly-and-reassembly-videos and visit our troubleshooting guides at http://trb.fyi/troubleshooting/ while you are at our page.

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

 
Video Index: 
Removing the Trigger and Trigger Bar – 0:35
Removing the Slide Catch Lever – 2:05
Disconnecting the Takedown Safety Lever – 2:54
Removing the Sear and Safety Lifter – 3:46
Removing the Safety Lever Housing – 5:36
Assembling the Safety Lever Housing – 6:47
Installing the Safety Lever Housing – 7:27
Installing the Safety Lifter and Sear – 8:48
Installing the Takedown Safety Lever – 12:16
Installing the Slide Catch Lever – 12:54
Installing the Trigger Bar and Trigger – 13:44

Our CZ 75B and Clone Frame Disassembly Video will walk you through disassembling the frame of a CZ 75B and its clones like the EAA Witness. 
 
This Video features an EAA Witness pistol which is a clone of the CZ 75B. There may be slight differences in this pistol to the CZ 75B however, the procedures should be extremely similar.
 
If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on CZ firearms and remember to subscribe while you are there. Also, make sure to visit the Full30 Forum located at https://forum.full30.com/ to interact with other gun owners in some awesome conversations about all aspects of our sport. While you are there stop by my profile (https://forum.full30.com/u/TheRogueBanshee/) to see what threads that we are active in.
 
To learn more about the tools that we used on the CZ 75B and Clone Field Strip Videos visit http://trb.fyi/tools-used-in-the-cz-75-and-cz-75-clone-videos/ and visit our troubleshooting guides at http://trb.fyi/troubleshooting/ 

Visit us at :
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  
 

Video Index: 
Removing the Trigger Spring - 0:36
Removing the Safety - 1:53
Removing the Sear Housing - 3:19
Disassembling the Sear Housing - 3:40
Removing the Trigger - 5:03
Removing the Hammer - 5:44
Removing the Magazine Catch - 7:07
Removing the Slide Stop Spring - 8:42

Our CZ 75B and Clone Frame Reassembly Video will walk you through Reassembling the frame of a CZ 75B and its clones like the EAA Witness. 
 
This Video features an EAA Witness pistol which is a clone of the CZ 75B. There may be slight differences in this pistol to the CZ 75B however, the procedures should be extremely similar.
 
If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  
 
To learn more about the tools that we used on the CZ 75B and Clone Field Strip Videos visit http://trb.fyi/tools-used-in-the-cz-75-and-cz-75-clone-videos/ and visit our troubleshooting guides at http://trb.fyi/troubleshooting/ 

Visit us at :
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  
 

Video Index: 
Installing the Slide Stop Spring - 0:35
Installing the Magazine Catch - 2:00
Installing the Hammer - 4:06
Installing the Trigger - 5:39
Assembling the Sear Housing - 8:55
Installing the Sear Housing - 11:22
Installing the Grips - 12:47

Our CZ 75B and Clone Slide Disassembly and Reassembly Video will show you how to disassemble a slide down to its individual components and then reassemble it.

This Video features an EAA Witness pistol which is a clone of the CZ 75B. There may be slight differences in this pistol to the CZ 75B however, the procedures should be extremely similar.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.

Visit our channel for more content on the CZ 75B and its clones and remember to subscribe while you are there.

For an article on the tools that we used on the CZ 75B visit http://trb.fyi/cz-75b-and-clone-field-strip-video and visit our troubleshooting guides at http://trb.fyi/troubleshooting/ while you are at our page.

Visit us at :

http://www.trb.fyi
http://www.facebook.com/TheRogueBanshee/
http://www.twitter.com/TheRogueBanshee
http://www.patreon.com/TheRogueBanshee


Video Index:
Removing the Firing Pin - 0:36
Removing the Extractor - 2:26
Installing the Extractor - 3:47
Installing the Firing Pin - 6:08

Our CZ 75B and Clone Field Strip Video will walk you through Field Stripping a CZ 75B and its clones like the EAA Witness. Field Stripping is an essential skill for the firearm owner to have since it is the basis for cleaning and doing basic maintenance.  

This Video features an EAA Witness pistol which is a clone of the CZ 75B. There may be slight differences in this pistol to the CZ 75B however, the procedures should be extremely similar.

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on the CZ 75B and its clones and remember to subscribe while you are there. 

For the tools that we used on the 1911 videos visit http://trb.fyi/cz-75b-and-clone-field-strip-video and visit our troubleshooting guides at http://trb.fyi/troubleshooting/ while you are at our page.

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

 
Video Index: 
History - 0:29
Checking for an unloaded firearm - 1:29
Removing the Slide from the Frame - 2:00
Removing the Recoil Spring from the Slide - 3:11
Removing the Barrel from the Slide - 3:57
Installing the Barrel into the Slide - 4:24
Installing the Recoil Spring into the Slide - 4:53
Installing the Slide onto the Frame - 5:50

Our Beretta 92/96/M9 Field Strip video will walk you through Field Stripping a Beretta 92, 96 and M9 for cleaning

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on Beretta firearms and remember to subscribe while you are there. 

For the tools that we used on the Beretta 92/96M9 videos visit http://trb.fyi/tools-used-in-the-beretta-92-96-m9-series-videos/ and visit our troubleshooting guides at http://trb.fyi/troubleshooting/ 

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

Video Index: 
History - 0:41
Checking for an unloaded firearm - 1:01
Removing the Slide from the Frame - 1:31
Removing the Recoil Spring Assembly - 2:23
Removing the Barrel - 3:11
Installing the Barrel - 3:37 
Installing the Recoil Spring - 4:01
Installing the Recoil Spring Assembly into the Slide - 4:21
Installing the Slide onto the Frame - 5:14

Our Glock Slide Disassembly and Reassembly Video will show you how to disassemble your Glock slide down to its individual components. After disassembly, we show you how to reassemble the slide. Also don’t forget to check out our Glock Frame Disassembly Video, Glock Frame Reassembly Video as well as our Glock Field Strip Video to learn more about the Glock pistols.

Our Glock video series should cover most models of Glock including:

9mm .40 10mm. .45 Auto .45 G.A.P. .380 Auto .357 Sig
G17 G22 G20 G21 G37 G42 G31
G19 G23 G29 G30 G38 G32
G26 G27 G40 G36 G39 G33
G34 G35 G41
G43

If you find our videos helpful please consider supporting us for free by using our affiliate banners and links on www.trb.fyi or by donating by becoming a Patron on Patreon http://www.patreon.com/TheRogueBanshee. Your support helps us continue providing high-quality content.  

Visit our channel for more content on Glock firearms and remember to subscribe while you are there. 

If you want to learn more about the tools used in the Glock Videos visit https://trb.fyi/tools-used-in-the-glock-videos If you need more information about troubleshooting visit our Glock Troubleshooting Guide at https://trb.fyi/glock-troubleshooting-guide/

Visit us at : 
 
http://www.trb.fyi  
http://www.facebook.com/TheRogueBanshee/  
http://www.twitter.com/TheRogueBanshee  
http://www.patreon.com/TheRogueBanshee  

Video index:
Removing the Slide Cover Plate - 0:41
Removing the Firing Pin Assembly - 1:47
Removing the Extractor - 3:34
Removing the Firing Pin Safety - 5:06
Assembling and installing the Firing Pin Safety - 5:49
Installing the Extractor - 7:02
Assembling and installing the Extractor Depressor Assembly - 7:40
Assembling and installing the Firing Pin Assembly - 8:38
Installing the Slide Cover Plate - 10:27

SHOW MORE

Created 1 year, 8 months ago.

46 videos

CategoryEntertainment

I am a part time FFL (I still work my day job), Firearms enthusiast and have been shooting since I was 10 years old. This channel was created as an outlet for showing various firearms related content including how I take down and put together various firearms.

I am in the process of moving my YouTube channel (youtube.com/theroguebanshee) due to changes in the firearm video policies. Please subscribe to my channel and consider supporting the work that I do here by becoming a Patron on Patreon. https://www.patreon.com/TheRogueBanshee or by using my affiliate links and banner ads on my blog site http://www.trb.fyi

More information can be found at my blog located at http://www.trb.fyi. I can also be found on the following platforms:

http://www.patreon.com/TheRogueBanshee
https://www.facebook.com/TheRogueBanshee/
https://twitter.com/theroguebanshee