Click to copy, then share by pasting into your messages, comments, social media posts and websites.
Click to copy, then add into your webpages so users can view and engage with this video from your site.
Report Content
We also accept reports via email. Please see the Guidelines Enforcement Process for instructions on how to make a request via email.
Thank you for submitting your report
We will investigate and take the appropriate action.
How To Do Metal Roof Valley Foam Insulation - Metal Roof Valley Foam
Phil shows you how to install valley foam on a metal roof. Sorry about the sound quality, there is a transcript of what he's saying.
⏱️⏱️Chapters⏱️⏱️
00:00 You'll want to put valley foam in, especially in snowy climates
00:23 Don't unroll it until you're ready to do the total area
00:39 Take the screws out and slide it under the edge of the metal in your valleys
01:00 Pulling the cover for the sticky side
01:30 Try to keep the tape low or you will cut it
🙏 Subscribe, 👍, it helps a lot!!
➤❓/ 💬: [email protected]
➤ Follow https://straightarrowrepair.com/pipf
➤➤I get a little for the channel-no charge for you if you use the links:
➤➤Shop Amazon https://amzn.to/3CxD1T4
➤➤Tool lists & recommended products🧰 https://straightarrowrepair.com/0lvf
➤➤Services We use
➤➤MORNINGFA·ME https://morningfa.me/invite/StraightArrowRepair
➤➤A2 Hosting http://www.a2hosting.com/refer/140244
➤➤Tubebuddy https://www.tubebuddy.com/StraightArrowRepair
➤➤Apsumo http://fbuy.me/v/philbridges
➤➤VidIQ: https://vidiq.com/straightarrowrepair
#Valleyfoam #metalroofing #roofinginsulation
Transcript:
Probably would or should. There's a lot of road noise, sorry. Should put valley foam in. Particularly when it snows, the water will go up that valley and go down underneath it, and will find a hole. This is valley foam. It comes in rolls as soon as you unroll this you need to prepare. It will continue to expand, and it expands to two and a half inches thick. So, it's meant to grow to the odd the angles that you put these valleys on and fill these ribs up with foam. So, the trick is going to be take these screws out, about 16 inches back that you've already put in. The screws should be an inch or two away so that they don't end up being in on the wrong side of the valley foam.
So, what you have got to do is take those screws out go to lift it up, and stick it underneath that edge. But uh, it's a pain sometimes because you've got deep hooks on that edge, and slide it underneath there with the sticky side, which would be this side here and it turns into clear right there down underneath. And then you, we'll show you how you can just pull it all off. As long as you keep it there. Under the roll there's a little strip to help you could grab it, put that underneath there, and you want to keep it low or you're going to end up cutting your, your peal off and you'll have to reach under there and get it again. It's kind of a pain, but just keep it low and ends up sticking like that. See that, I cut it so I have to reach under there and grab it anyway. Just keep peeling it up and then that will stay in place and you put your screws back in.
There you go.
how to do metal roof valley foam insulation,installing a metal roof,metal roof diy,metal roof installation,metal roof over shingles,metal roof valley,metal roofing installation,metal roofing learning channel,metal roofing valley,Straight Arrow Repair,valley foam metal roof,valley trim installation,sheet metal,metal ro
Category | DIY & Gardening |
Sensitivity | Normal - Content that is suitable for ages 16 and over |
Playing Next
Related Videos
21 hours ago
Handyman Work What Happens in a Week
1 day, 9 hours ago
Why We Do The Videos The Way We Do #Shorts
1 day, 15 hours ago
5 days, 2 hours ago
6 days, 5 hours ago
6 days, 19 hours ago
Warning - This video exceeds your sensitivity preference!
To dismiss this warning and continue to watch the video please click on the button below.
Note - Autoplay has been disabled for this video.